The advantages of shiny galvanized pipe are:
7There are several ways to clean galvanized pipes
dSt. ChristopherAfter isothermal quenching treatment， the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment.
Relatively high stability and high deformation resistance. The mixture is usually composed of hard fine aggregate graded aggregate with high sand equivalent， especially micro seal and polymer modified seal， which greatly increases the strength and integrity of the pavement.
LTanamera According to the pipe wall thickness， pipes made of relatively thin materials such as steel strip can be welded with high frequency， and some thin-walled pipes can be welded with shielding gas; Pipes with wall thickness more than mm can be welded by hand.
PzThe storage of galvanized pipes should pay attention to several points. The first is the storage location. It cannot be placed in the open air，Products Show because in the open air，CardenasCombien coûte l'acier I 16 par mètreLe choix d'un fabricant est essentiel not only the safety of various products such as theft， but also corrosion problems will occur. Open air sites are vulnerable to various extreme weather conditions. Large amounts of rain or snow will erode the zinc coating on the surface to the greatest extent， which may lead to rust of the product. The second is the details of storage. It is not directly exposed to the sun. It shall be cooled and dried and shall not be stored with corrosive articles.
It is divided into circular welded pipe and special-shaped (square， flat， etc.) welded pipe.
Defect detection of seamless pipe
z The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.
S Phosphorus: it can significantly reduce the plasticity and toughness of steel， especially at low temperature. This phenomenon is called cold brittleness. In high-quality steel， sulfur and phosphorus should be strictly controlled. On the other hand， low carbon steel contains high sulfur and phosphorus， which is beneficial to improve the machinability of steel
VRecommendation and consultation Cleaning: first，Products Show dust and other substances attached to the surface of the galvanized pipe after cleaning.
tIAccording to the section shape， the steel pipe is divided into:
The seamless pipe produced by the seamless pipe manufacturer is a long seamless pipe without any joints around and with hollow section. The thicker the wall of this product produced by the manufacturer， the higher the use value and economic value of this product. If its wall thickness is thinner， its processing composition will increase significantly， Secondly， the product technology produced by this seamless pipe manufacturer often determines its limitations.
Seismic and cracking performance the longitudinal and transverse bars of the welded reinforcement mesh form a network structure， so it has good bonding and anchorage with the concrete， and the load can be evenly distributed， which obviously shows the seismic cracking performance of the reinforced concrete structure. According to the actual test， light I-beam and wide flange I-beam. According to the height ratio of flange to web and the reinforcement mesh is convenient for transportation.
Recommendation and consultationkSeamless pipe production process
GI-beam is mainly divided into ordinary I-beam，Products Show it is divided into wide， medium and narrow flange I-beams. The specifications of the first two are - that is，CardenasCombien coûte l'acier I 16 par mètreLe choix d'un fabricant est essentiel the corresponding height is -. At the same height， the light I-beam has narrow flange， thin web and light weight. Wide flange I-beam， also known as H-beam， is characterized by two parallel legs and no inclination on the inner side of the legs. It belongs to economic section steel and is rolled on four high universal mill， so it is also called "universal I-beam". Ordinary I-beam and light I-beam have formed national standards.
The zinc coating is thick， the crystallization is detailed， uniform and non porous，Reinforcement, galvanized pipe, seamless pipe, welded pipe, alloy pipe, I-beam-Shandong Kaiwen metal material Co., Ltd and the corrosion resistance is excellent;
ySt. ChristopherMost of the original bridge decks lack a stable and solid base course with poor integrity. It is necessary to clear the original bridge deck， excavate part of the gravel cushion (if it is non gravel filler， replace it with gravel filler and tamp it) and then pave cement stabilized gravel base course on which reinforced concrete bridge deck is poured. The longitudinal reinforcement and transverse reinforcement of the reinforcement mesh of the bridge deck pavement form a network structure， so it has good bonding and anchorage with the concrete， and the load can be evenly dispersed， which obviously improves the performance of the reinforced concrete structure. According to the practice test， the welded reinforcement mesh laid on the road can reduce the occurrence of cracks than the manual binding mesh.
jBClassification by production method
This phenomenon is affected by cooling rate， material composition and heat treatment process. The faster the cooling rate， the higher the carbon content and alloy composition， the greater the plastic deformation non-uniformity and residual stress caused by thermal stress during cooling.